CANNA - CALMAG AGENT
CANNA Calmag Agent adds calcium and magnesium to the irrigation water and helps bring the solution to a mineral concentration more suitable for plant nutrition. It is particularly useful when starting with very soft water or water obtained by reverse osmosis.
What is CANNA Calmag Agent used for?
CANNA Calmag Agent adds calcium and magnesium to the irrigation water. It is useful when starting with very soft water or water produced by reverse osmosis.
It alters the base to which nutrients and additives are added, increasing the initial conductivity.
The choice depends on the characteristics of the water, not just the growing medium: hard water or water containing sodium and chlorides require different assessments.
Technical data sheet
| Calcium and magnesium supplement | |
| Freshwater: 0.1–0.5 ml/L; EC reference approx. 0.4–0.45 mS/cm before adding nutrients | |
| Before adding the base nutrient | |
| Water adjustment; measure the EC | |
| Fresh water or reverse osmosis water | |
| NPK 6-0-0; total N 6.0% (5.1% nitrate and 0.9% urea); CaO 6.8%; MgO 2.4% |
Formulation and product selection
EC describes the total conductivity and does not indicate which salts are present: for this reason, a mineralised water source must be assessed on a case-by-case basis.
Added before the nutrients, the product forms the basis of the programme; the final EC includes all components and should not be compared with that of water alone.
Effects on the plant and flowers
Calcium and magnesium are the elements that CalMag Agent supplements when the source water is deficient in these minerals, i.e. classified as soft. Under these conditions, the product helps to reduce calcium and magnesium deficiencies and improve nutrient uptake, resulting in more robust plants and higher-quality flowers.
The product also increases the electrical conductivity (EC) of the water; therefore, with water that is already rich in minerals, it may be unnecessary and cause the solution to exceed the useful range. If the water is already of good quality, the amount of nutrients to be added may even be reduced.
Benefits for cultivation
More balanced water. With soft water, CalMag Agent raises calcium and magnesium levels to a level more suitable for the solution. The result depends on the quality of the source water.
Stronger plants. With calcium and magnesium readily available, the plant’s structure is more robust and nutrient uptake is more consistent.
Directions for use
Shake and add the product to the water before adding any other nutrients. For soft water, the instructions specify 0.1–0.5 ml/L, with a reference EC of approximately 0.4–0.45 mS/cm before adding nutrients: these are guide values, not a fixed dose for all water types.
If using a pre-mineralised water source, the dosage may vary or not be necessary: check the water composition and the instructions for the CANNA plan you are following.
Related products
- CANNA Mono Calcium — A liquid supplement designed to specifically target calcium intake.
- CANNA Mono Magnesium Mg 7% — A concentrated liquid magnesium supplement; magnesium is involved in photosynthesis and chlorophyll formation.
- CANNA Hydro Vega A+B — This is the basic two-part nutrient solution for the vegetative phase in hydroponic systems.
CANNA: research and programmes for every growing medium
Since the early 1990s, CANNA has been developing fertilisers and growing media for growers using soil, coconut fibre or hydroponics. Its approach stems from a practical question: what changes when the growing medium changes? This has led to the creation of distinct product ranges, comprising basic nutrients and complementary products designed to be used in sequence. Research, testing and consultation with growers are integral to the company’s history, which aims to make the choice of programme – from the first nutrient to the additives – as straightforward as possible.
CANNA states that it carries out research, laboratory testing and formulation development in-house. According to its presentation, the development of a new product takes on average around two years: a process that involves the design of specific product ranges for different growing media and cultivation systems.
CANNA Calmag Agent adds calcium and magnesium to the irrigation water and helps bring the solution to a mineral concentration more suitable for plant nutrition. It is particularly useful when starting with very soft water or water obtained by reverse osmosis.
What is CANNA Calmag Agent used for?
CANNA Calmag Agent adds calcium and magnesium to the irrigation water. It is useful when starting with very soft water or water produced by reverse osmosis.
It alters the base to which nutrients and additives are added, increasing the initial conductivity.
The choice depends on the characteristics of the water, not just the growing medium: hard water or water containing sodium and chlorides require different assessments.
Technical data sheet
| Calcium and magnesium supplement | |
| Freshwater: 0.1–0.5 ml/L; EC reference approx. 0.4–0.45 mS/cm before adding nutrients | |
| Before adding the base nutrient | |
| Water adjustment; measure the EC | |
| Fresh water or reverse osmosis water | |
| NPK 6-0-0; total N 6.0% (5.1% nitrate and 0.9% urea); CaO 6.8%; MgO 2.4% |
Formulation and product selection
EC describes the total conductivity and does not indicate which salts are present: for this reason, a mineralised water source must be assessed on a case-by-case basis.
Added before the nutrients, the product forms the basis of the programme; the final EC includes all components and should not be compared with that of water alone.
Effects on the plant and flowers
Calcium and magnesium are the elements that CalMag Agent supplements when the source water is deficient in these minerals, i.e. classified as soft. Under these conditions, the product helps to reduce calcium and magnesium deficiencies and improve nutrient uptake, resulting in more robust plants and higher-quality flowers.
The product also increases the electrical conductivity (EC) of the water; therefore, with water that is already rich in minerals, it may be unnecessary and cause the solution to exceed the useful range. If the water is already of good quality, the amount of nutrients to be added may even be reduced.
Benefits for cultivation
More balanced water. With soft water, CalMag Agent raises calcium and magnesium levels to a level more suitable for the solution. The result depends on the quality of the source water.
Stronger plants. With calcium and magnesium readily available, the plant’s structure is more robust and nutrient uptake is more consistent.
Directions for use
Shake and add the product to the water before adding any other nutrients. For soft water, the instructions specify 0.1–0.5 ml/L, with a reference EC of approximately 0.4–0.45 mS/cm before adding nutrients: these are guide values, not a fixed dose for all water types.
If using a pre-mineralised water source, the dosage may vary or not be necessary: check the water composition and the instructions for the CANNA plan you are following.
Related products
- CANNA Mono Calcium — A liquid supplement designed to specifically target calcium intake.
- CANNA Mono Magnesium Mg 7% — A concentrated liquid magnesium supplement; magnesium is involved in photosynthesis and chlorophyll formation.
- CANNA Hydro Vega A+B — This is the basic two-part nutrient for the vegetative phase in hydroponic systems.
CANNA: research and programmes for every growing medium
Since the early 1990s, CANNA has been developing fertilisers and growing media for growers using soil, coconut fibre or hydroponics. Its approach stems from a practical question: what changes when the growing medium changes? This has led to the creation of distinct product ranges, comprising basic nutrients and complementary products designed to be used in sequence. Research, testing and consultation with growers are integral to the company’s history, which aims to make the choice of programme – from the first nutrient to the additives – as straightforward as possible.
CANNA states that it carries out research, laboratory testing and formulation development in-house. According to its presentation, the development of a new product takes on average around two years: a process that involves the design of specific product ranges for different growing media and cultivation systems.
Recalculation in progress …